Dolphin, the GameCube and Wii emulator - Forums
Super Smash Bros Melee - Printable Version

+- Dolphin, the GameCube and Wii emulator - Forums (https://forums.dolphin-emu.org)
+-- Forum: Dolphin Emulator Discussion and Support (https://forums.dolphin-emu.org/Forum-dolphin-emulator-discussion-and-support)
+--- Forum: Support (https://forums.dolphin-emu.org/Forum-support)
+--- Thread: Super Smash Bros Melee (/Thread-super-smash-bros-melee--36276)

Super Smash Bros Melee - dinomite07 - 08-03-2014

[Image: 5rPJ9V0.png]
[Image: w43Vj9I.png]

I used Dolphin 4.02 stable from this site and I clicked [Image: EQEvoKI.png] Then I loaded the iso and go to the screen below.

[Image: RwH98uL.png]
It is just stuck at that screen. I can't make a new game data or do anything at all.

RE: Super Smash Bros Melee - JMC47 - 08-03-2014

Did you configure your controller?

RE: Super Smash Bros Melee - neobrain - 08-03-2014

Why do you use 32 bit builds?

RE: Super Smash Bros Melee - dinomite07 - 08-03-2014

um just using keypad and mouse do you need a controller?

RE: Super Smash Bros Melee - dinomite07 - 08-03-2014

bump.

RE: Super Smash Bros Melee - Shonumi - 08-03-2014

JMC47 was asking if you configured the controller, but you didn't answer him. You have to set up your GCPad (click that button) and make sure you setup your input correctly. Also, make sure the GC controller is "plugged in" by clicking Config, going to the GC tab, and making sure Port 1 says "Standard Controller". With that, just press whatever key you assigned to represent the A Button and you should be able to get past that screen.

EDIT: And to answer your question, no you don't need a controller. A keyboard works just fine.

RE: Super Smash Bros Melee - dinomite07 - 08-03-2014

(08-03-2014, 08:49 AM)Shonumi Wrote: JMC47 was asking if you configured the controller, but you didn't answer him. You have to set up your GCPad (click that button) and make sure you setup your input correctly. Also, make sure the GC controller is "plugged in" by clicking Config, going to the GC tab, and making sure Port 1 says "Standard Controller". With that, just press whatever key you assigned to represent the A Button and you should be able to get past that screen.

EDIT: And to answer your question, no you don't need a controller. A keyboard works just fine.

ty works just fine i just didnt know what to put in slot 1

[Image: 15XEt3t.jpg]
FPS is set to 120. Game audio and the game iteslf is laggy.

RE: Super Smash Bros Melee - DJBarry004 - 08-03-2014

What´s the point of that? Your CPU is pretty underpowered to reach a speed like that, anyway...

RE: Super Smash Bros Melee - dinomite07 - 08-03-2014

(08-03-2014, 09:38 AM)DJBarry004 Wrote: What´s the point of that? Your CPU is pretty underpowered to reach a speed like that, anyway...
What settings do you think I should use?

RE: Super Smash Bros Melee - Shonumi - 08-03-2014

There are no magic settings. Slow CPUs will run Dolphin slowly. There's no getting around that. 40FPS is pretty good speed considering your hardware.