Bluetooth Dongle/ Driver issues and no Sync

[Crazyhalo]

Hey Everyone, I'm coming here as a last resort simply because I cannot for the life of me figure out whats wrong with my setup, my situation is that I have finally bought a wii sensor bar(wireless), USB Bluetooth Dongle from Rocketfish, and appropriate wiimote and nunchuck(Wiimotionplus) version. Now I set up my bluetooth icon to add a device and go through the motions( holding 1+2) etc etc, after discovery though two things happen, 1. the device drivers don't install correctly, this error happens most of the time or 2, Windows recognizes the wii-mote correctly and installs correctly, at this point I'll move into Dolphin, hit Pair up and hit 1+2 on the wii mote, it recognizes the wii mote is there as well saying a wii mote is connected both at the window and in the log(I also do have my input selected as a real wii mote), all of this works BUT there is no response from the game and the 4 lights on the wii mote continuously flash, it doesn't enumerate itself as player one, I'm really at a loss here anyone some help please? Thanks in advance
EDIT: One more situation, 3rd is same as described above but the lights do not contiue to flicker and the wii mote disconnects after about 10 seconds of no input

[ExtremeDude2]

Are you using an official wiimote?

[Crazyhalo]

1. (12-24-2012, 08:28 AM)ExtremeDude2 Wrote: Are you using an official wiimote?

   
   
   By appearence yes, has official nintendo seal, serial numbers etc, doesnt have that crappy feel either, I'm reading around that the problem may be cause its motion plus

[Soopah]

(12-23-2012, 08:06 AM)Soopah Wrote: http://forums.dolphin-emu.org/Thread-rvl-cnt-01-tr?pid=230406#pid230406

post 453
afaik RVL-cnt-01-TR work only with ToshibaStack (maybe Im wrong), (you don't need a toshiba BTdongle to use the program)


the important part is to press A to connect the wiimote,
1+2 is for syncing (when you connect it 1st time, or when you change batteries)

Maybe time to sticky that thread?

[ExtremeDude2]

Good thing I have the addon I guess :p

[Crazyhalo]

(12-24-2012, 08:53 AM)Soopah Wrote:

(12-23-2012, 08:06 AM)Soopah Wrote: http://forums.dolphin-emu.org/Thread-rvl-cnt-01-tr?pid=230406#pid230406

post 453
afaik RVL-cnt-01-TR work only with ToshibaStack (maybe Im wrong), (you don't need a toshiba BTdongle to use the program)


the important part is to press A to connect the wiimote,
1+2 is for syncing (when you connect it 1st time, or when you change batteries)

Maybe time to sticky that thread?

Its a huge step but Im falling into a few problems even still, it says it installs but then disconnects a bit later, perhaps I've installed toshiba btstack incorrectly?, Got a specific step by step solution? sorry for asking too much

[Soopah]

(12-24-2012, 09:12 AM)Crazyhalo Wrote:

(12-24-2012, 08:53 AM)Soopah Wrote:

(12-23-2012, 08:06 AM)Soopah Wrote: http://forums.dolphin-emu.org/Thread-rvl-cnt-01-tr?pid=230406#pid230406

post 453
afaik RVL-cnt-01-TR work only with ToshibaStack (maybe Im wrong), (you don't need a toshiba BTdongle to use the program)


the important part is to press A to connect the wiimote,
1+2 is for syncing (when you connect it 1st time, or when you change batteries)

Maybe time to sticky that thread?

Its a huge step but Im falling into a few problems even still, it says it installs but then disconnects a bit later, perhaps I've installed toshiba btstack incorrectly?, Got a specific step by step solution? sorry for asking too much

Remove batteries, remove any connection you'd make in toshibastack, reboot computer.


Then add new connection, you choose Express mode.

app is searching , you press 1+2 (LED blink)
wiimote found and you wait until LED is OFF
next
the app will talk about PIN code, you press A, and voila! (LED is OFF)

Launch Dolphin open Wiimote config (select Real Wiimote), and press refresh.


When you don't play you have to disconnect your wiimote with toshibastack.

Next time, right click in toshibastack and connect, then ok and press A.

[Crazyhalo]

(12-24-2012, 09:29 AM)Soopah Wrote:

(12-24-2012, 09:12 AM)Crazyhalo Wrote:

(12-24-2012, 08:53 AM)Soopah Wrote:

(12-23-2012, 08:06 AM)Soopah Wrote: http://forums.dolphin-emu.org/Thread-rvl-cnt-01-tr?pid=230406#pid230406

post 453
afaik RVL-cnt-01-TR work only with ToshibaStack (maybe Im wrong), (you don't need a toshiba BTdongle to use the program)


the important part is to press A to connect the wiimote,
1+2 is for syncing (when you connect it 1st time, or when you change batteries)

Maybe time to sticky that thread?

Its a huge step but Im falling into a few problems even still, it says it installs but then disconnects a bit later, perhaps I've installed toshiba btstack incorrectly?, Got a specific step by step solution? sorry for asking too much

When you click add new connection, you choose Express mode.

app is searching , you press 1+2 (LED blink)
wiimote found and you wait until LED is OFF
next
the app will talk about PIN code, you press A, and voila! (LED is OFF)

Launch Dolphin open Wiimote config (select Real Wiimote), and press refresh.


When you don't play you have to disconnect your wiimote with toshibastack.

Next time, right click in toshibastack and connect, then ok and press A.

Toshiba stack is acting odd, the installation asks to plug in the bluetooth device and press okay even though it was I can't manage to install it properly

[Soopah]

I don't know, maybe uninstall toshibastack and other bluetooth driver, then plug your BTdongle installing windows drivers, and after install ToshibaStack.

Or, your dongle is not compatible :/

[Crazyhalo]

(12-24-2012, 09:40 AM)Soopah Wrote: I don't know, maybe uninstall toshibastack and other bluetooth driver, then plug your BTdongle installing windows drivers, and after install ToshibaStack.

Or, your dongle is not compatible :/
Well the dongle keeps installing its own drivers unfortunately
any tips or workaronds maybe disabling its function?